Tips and Tricks for Above Ground Pool Installation | Pool Supplies Canada (2022)

It is possible to install your above ground pool yourself. With a little time and effort, you can save a lot of money. Once you’ve planned for and purchased your above ground pool package the next step is to actually install the pool. These tips and tricks will make for a smooth installation:

Gather Your Tools Before You Start

You should have the following tools on hand. Anything you don’t have you can borrow from a friend or rent from your local hardware store:

(Video) How to Install Your own Above Ground Pool - Customer Guide - Pool Supplies

  • Tape measure
  • Level
  • Shovel
  • Rake
  • Trowel
  • Phillips head screwdriver
  • Wrench (5/16 and ¼)
  • Duct tape
  • Sand (use very fine sand that is easily compacted)
  • Filter
  • Skimmer
  • Patio blocks (2” x 8” x 16”) are not necessary but can make the installation easier
  • Transit (rent this)
  • Sod remover (rent this)
  • Shop Vac
  • Drill

Check Your Pool Package to Ensure You Have All the Pieces

Check your pool package materials against the materials listed in the instructions to ensure you have all the pieces before you get started. Call Pool Supplies Canada immediately if you are missing anything.

After you have opened and counted the hardware packets to ensure you’re not missing anything organize and sort everything so you have it on hand. Don’t mix the different sizes of nuts or screws, or drop or lose any pieces.

The Ground Work

Ensure the Ground is Level and Prepare It for Construction

Part of proper pool planning includes choosing the area for your pool and obtaining the permits to install your pool. Once that has been completed the next step is to ensure the ground is level. This is a critical step to ensure your pool is structurally sound and safe.

(Video) Above Ground Pool Plumbing Step-by-Step From Pool Supplies Canada

To make sure your ground is level you can either:

  • Rent a transit from your local hardware store or equipment rental outlet.
  • Use a long, straight board with a carpenter’s level on top of it to measure the levelness of the area.
  • The entire area should be within 1 inch of being perfectly level.
  • If the ground is not level dig down any high areas (don’t build up low areas) to prevent the pool from settling over time.
    • Once the ground is level you need to take measurements before starting construction:

      Find the center point (where the middle of your pool will be). Use an existing object (like the wall of your house) and measure the area and mark where the edges of the pool will go. Measure half the width (the radius) of the pool from the marked edges. This is your center point. Mark the center.

      Use a soft measuring tape to measure around the perimeter of the pool. Measure the outline of your pool using the radius mentioned above so you have a guideline for construction. Add one foot to the measurement and then mark the ground around your center point, following the pool shape and measurements given in the instructions.Use stakes to mark the ground.

      Remove sod and rake the area:

      Pools can’t be installed on grass. The grass will rot and affect the pool liner. Plus, grass can shift or settle over time, making it unstable. This means you need to remove the sod from the marked area. Rent a sod remover from your local hardware store or equipment rental shop to make this job easier.Once you’ve dug up the sod you need to rake the area to remove any remaining grass, roots, rocks or other debris (all of which can negatively affect the liner).Check that the area is level again. This is such a critical step it’s important to check everything is level over and over again throughout the installation process.

      (Video) Round Above Ground Pool Installation - Pool Supplies

      Tips for Preparing the Ground:

      • If the ground is clay use a floor pad for the installation
      • Oval buttress free pools require additional room at the sides for the ungrounded leg supports
      • You can not install an oval pool on concrete
      • Don’t install a floor pad on a dished pool because the floor pad is designed to lay flat
      • You can not dish an oval pool if it has strapping
      • The pool must be level across the perimeter
      • For areas with severe weather or cold, a 6 inch base is recommended rather than a 2 inch base

      Construction of Your Above Ground Pool

      Build the bottom ring:

      Follow the instructions that come with your above ground pool package as each type, brand and size of pool have different instructions. In general, you will be using your plates, stabilizers and rails. Here are some tips to identify each piece:

      • Your plates will be made of metal or resin
      • The bottom stabilizer should be crimped on one side. It has smaller rails
      • The bottom rail is straighter and larger than the stabilizer.
      • Lay out the pieces and assemble as instructed. Generally, you will be sliding the bottom rail into the bottom plate up to the dimple on the plate.
      • Remember to measure the bottom track in several locations to ensure that the pool is truly round and the correct size. If the size is correct, stake the ring into position. If not, contact Pool Supplies Canada immediately.On oval pools make sure diagonal measurements match (see your pool diagram for these measurements). Double and triple check the diagonal measurements and keep doing this over and over.

      Support your base:

      Once your ring is in place you will need to add support for the base of your pool to keep it stabilized and level over time. This involves:

      • Levelling each plate to within ½ inch of each other.
      • Using patio blocks under each bottom plate. (not required) Place the block in the ground so the track is flush on the ground and level in all directions. If you choose to use patio blocks, make sure they are perfectly level and flush with the ground. All patio blocks must be flush with the ground, solid and level with each other in all directions.
      • Remove one bottom rail so you can fill the area with sand. Mark the connecting bottom plates so that you can place them back in the right spot after you have filled the area with sand.
      • The amount of sand you will need will depend on the size of your pool. Usually between 1 – 6 yards is enough.
      • Replace the bottom rail and spread the sand evenly across the pool area.
      • Don’t spill sand on the bottom rails. If you do, be sure to clear sand or stone dust from the bottom rails otherwise the wall will buckle.

      You’ve completed the hard part! The next step is to assemble and install the pool, following the manufacturer’s instructions. If you have any questions about your instructions contact the experts at Pool Supplies Canada.

      (Video) A Customer's DIY Inground Pool Installation - Pool Supplies

      Tips to Install the Pool Wall:

      • As you unroll the wall put the top plates on to help support and give the pool strength.
      • Make sure the skimmer cut is on the top portion of the wall.
      • If your pool has buttresses:

        • Make sure gaps are tight along the wall where the buttresses are.
        • On oval pools the first buttress that you install will be the reference to install the remaining buttresses, therefore ensure that measurements and placements are exactly where they need to be.
      • Use stakes around the pool to hold the wall up while you are installing it.
      • If you find that the wall hasn’t aligned properly once you have finished placing the wall tracks in the bottom plates, then adjust the bottom rails of the plate (moving them in or out) to ensure they fit properly. Do this evenly throughout the pool if needed.
      • Don’t skip any nuts or bolts or your pool will not be stable.
      • Staggered wall bar systems don’t have pre-attached bars. Connect the bars yourself using the nuts and bolts provided.
      • Wall bars must not touch each other.
      • Build a 6-8-inch cove along the inside of the pool wall. The cove is an important part of the pool structure. Take your time to make a complete, full-sized cove.
      • Pack your cove. Be careful not to scratch the pool wall when you’re doing this. You can use a trowel.
      • If the pool wall is floating, there is probably dirt in the track. To correct this issue, lift the wall and use a shop vac to clean it out. If you can't lift the wall you might have to dissemble the pool structure to correct this.
      • If your pool has strapping:

        • Ensure that the straps raise higher in the middle. This may require you to put a little more stone dust underneath. If you fail to do this the straps will lift when the pool is filled with water.
        • On oval pools the strapping may begin to float. To troubleshoot this problem, check all measurements to ensure the pool is built correctly. Secondly ensure you raised the straps by 0.5 inches in the centre.
        • Do not be alarmed if you are not using all of the holes in the strap end channels.
      • If holes do not align, DO NOT drill holes! Verify the alignment of the structures.If the holes are still not aligning stick a screwdriver through two of the holes to help line up the ends of the wall.

      Installing the Pool Liner and filling

      Tips to Install the Pool Liner:

      • Be careful not to tear the liner during installation.
      • You must install the liner on a warm, sunny day and check to ensure the evening temperature doesn’t dip too low.
      • Lay the liner in the sun for a few hours before you start so it is easier to lay out. Liners are usually slightly smaller than the pool’s support structure and it will stretch more easily when it is warm out. You should not install a liner on a cold day or fill the pool with very cold water once the liner has just been installed.
      • Wet the sand and then rake it before putting the liner in the pool. This will ensure a level base
      • Do not step on the liner with your shoes on. Install it either barefoot or in socks.
      • Make sure you don’t track any rocks into the pool with you while you are walking on the liner towork the wrinkles out.
      • Work all the wrinkles to the outside of the pool.
      • Once the stabilizer rails are installed you can take down the landscaping stakes.
      • This is the last chance you have to ensure the bottom of your pool is level and free of debris
      • Do not trim off the excess liner. If the liner ever needs to be removed, trimming the liner willmake re-installation very difficult. Instead, roll up any excess liner and tape it in place near the top of the pool wall.

      Tips for Different Types of Liners:

      • Snap Bead liners snap into a separate track around the pool and are installed on top of the pool wall.
      • V-Bead liners require no coping. The stabilizer rails will hold this liner in place.
      • Unibead liners can be used as either a Snap Bead or a V-Bead liner. It comes as a V-Bead but you can remove the top portion to make it a Snap Bead liner.
      • Overlap liners are hung over the pool wall. These are securing using plastic coping strips.

      Tips for Installing Plates, Rails, Covers:

      • Follow manufacturer’s instructions carefully. The pieces should all fit together easily.
      • Check to ensure the sides and top are level.
      • Make sure the top plates are perfectly straight using a level before you tighten them.
      • Bottom rails must always be held in place in the bottom plate.
      • You must recheck the gaps at each and every one of the bottom rails so that they are all equal in gap size.

      Tips for Filling Your Pool

    • Fill the pool half way first and then install the skimmer and filter according to manufacturer’s instructions.
    • Install the safety warnings because your warranty could be voided if you don’t add these labels.
    • Apply the safety warnings before filling your pool to the top.
    • The water level should be one third to half way up the skimmer.

    If you have any questions, concerns or need assistance contact Pool Supplies Canada to speak directly to one of our pool installation experts.

    With these steps you are now ready to install your own Above Ground Pools


What is the best thing to put underneath an above ground pool? ›

Concrete pads are excellent to use as a base for your above ground pool, but you'll want to add another cushion between the two. Concrete is an abrasive material and will wear on the liner if it's in direct contact. Concrete is the best choice for a solid base because it is perfectly flat.

How do you set up an above ground pool for the first time? ›

How to Open Your Above Ground Pool Like a Pro
  1. Pull the Cover Off the Pool. ...
  2. Prepare your Pool Cover for Storage. ...
  3. Fill the Pool with Water. ...
  4. Goodbye Winter Pool Plugs and Hello Skimmer Baskets. ...
  5. Re-Install Your Pump, Filter, and Equipment. ...
  6. Start Up Your Pump and Filter. ...
  7. Clean Up Duty. ...
  8. Shock The Pool.
Feb 13, 2021

What do you put in an above ground pool when you first fill it up? ›

Once the pool is opened and the floor and walls have been brushed the first chemical you should add is chlorine to shock it. It's recommended you add a gallon of liquid chlorine or pound of granular chlorine for every 5,000 gallons of water in the pool. You can also add more chlorine at the end of the opening process.

What supplies do I need for an Intex pool? ›

The following pool accessories are necessary for maintaining an Intex pool:
  • An above-ground pool vacuum.
  • A skimmer (long net on a pole)
  • Floating chlorine tablet dispenser.
  • Pool maintenance kit (pH and chlorine testing kit)
  • Pool cover to keep the pool clean/prevent evaporation of water.
  • Shock chemicals or a saltwater system.

Should I put sand under my above ground pool? ›

Sand is the recommended base material upon which an aboveground pool should sit. Sand is used under an aboveground pool to protect the pool's vinyl liner from rocks and objects that could tear the liner. Also, sand under an aboveground pool acts as cushioning for its floor, making it more comfortable for feet.

What kind of sand goes under an above ground pool? ›

Mason sand, sometimes called mortar sand, can normally be found at any sand/gravel yard or masonry supply yard. It is usually measured in yards. It is very fine and should not contain any rocks or pebbles. This will create a very smooth bottom and is the most popular method to use when installing an above ground pool.

How do you smooth the bottom of an above ground pool? ›

When your pool is ready for swimming, put on a pair of soft-soled shoes and go for a walk in your pool. As you walk around on the liner, gently stretch the wrinkles from one side and then the other using your feet. This stretching should help smooth out minor wrinkles.

How much sand goes under an above ground pool? ›

It is commonly recommended by above ground pool manufacturers to have a 2" sand base inside the pool, under the liner. This will help protect your liner, and provide a soft floor that provides comfort while walking in your pool. Always use masonry sand, which is a washed sand, free of rocks and debris.

How soon after filling a pool Can you swim? ›

Chlorine/non-chlorine chemicals – When adding chlorine or non-chlorine chemicals to “shock” your pool after a fill-up, wait about 24 hours or until levels are approximately 5 ppm. If you'll only be adding liquid chlorine, it's generally safe to swim after about 4 hours or until levels are 5 ppm or lower.

What do I need for my small above ground pool? ›


How can I make my above ground pool more fun? ›

Get a floating ping pong table and show off your mad ping pong skills in the pool. Floating tables and waterproof cards can make your above ground pool the perfect place for a poker night. Lap swimming more your style? Doughboy pools can be special ordered in a couple of sizes specifically designed for lap swimming.

Do you need a fence around your above ground pool? ›

The CPSC recommends surrounding all pool areas with childproof fencing and gates, and that goes for above-ground pools, too. Above-ground pools have elevated edges that toddlers can't reach, but stairs and ramps that provide access to the pool's surface should be secured with gates and childproof locks.


1. Pool Supplies Canada Above Ground Pool and Deck Build
(Pool Supplies Canada)
2. Facts Nobody Told You About Above Ground Pools
3. Oval Above Ground Pool Installation (Buttress-Free) - Pool Supplies
(Pool Supplies Canada)
4. Above Ground Pool Plumbing Step-by-Step (With Voiceover) - From Pool Supplies!
(Pool Supplies Canada)
5. Round Above Ground Pool Installation from Pool Supplies Canada
(Pool Supplies Canada)
6. Oval Above Ground Pool Installation (with Buttresses) - Pool Supplies
(Pool Supplies Canada)

You might also like

Latest Posts

Article information

Author: Ms. Lucile Johns

Last Updated: 05/28/2022

Views: 5801

Rating: 4 / 5 (41 voted)

Reviews: 80% of readers found this page helpful

Author information

Name: Ms. Lucile Johns

Birthday: 1999-11-16

Address: Suite 237 56046 Walsh Coves, West Enid, VT 46557

Phone: +59115435987187

Job: Education Supervisor

Hobby: Genealogy, Stone skipping, Skydiving, Nordic skating, Couponing, Coloring, Gardening

Introduction: My name is Ms. Lucile Johns, I am a successful, friendly, friendly, homely, adventurous, handsome, delightful person who loves writing and wants to share my knowledge and understanding with you.